To make initial diagnostics, the PC-3000 universal utility is launched. There are special PC-3000 adapters used for switching the HDD into technological mode to get access to the internal HDD software and user data. HDD diagnosis can be done in standard (user) and technological (factory) modes. The PC-3000 allows you to diagnose the HDD, fix damaged HDD modules, switch off defective heads, block access to the damaged area of magnetic surfaces, get access to the user data and many other functions. If one of these parts is damaged, the HDD does not work. The main principles of PC-3000 functionalityĪ Hard Disk Drive (HDD) consists of three main parts: the Hard Drive Assembly, the printed circuit board and the internal software. For instance, four processes can be launched for each port or two processes can be launched: the first one works with three ports and the second one only with one port and so on. Once a process is started it can use any number of PC-3000 Express ports. The "PC-3000 Resource manager" manages port and related process activity, controls the status of the ports, checks process conditions and kills processes when it is necessary. The "PC-3000 Resource manager" software makes using the new PC-3000 Express very easy and effective. One of the most important new features of the PC-3000 Express is to allow for launching of the PC-3000 utility and the Data Extractor tasks as separate OS processes. Resource Management of the PC-3000 Express board Welcome to our Blog to read more about the new features and learn how to use them. Triggered protection system turns off the voltage on the corresponding channel. The Power Supply Unit is equipped with a sound speaker which signals about the PC power supply unit failure or HDD overcurrent. Power voltage oscilloscope screen after HDD start This feature allows to perform advanced HDD diagnostic and determine the cause of failure. You can get a graph visually representing the precise information about the current power status in real time. The intelligent Power Supply Unit of PC-3000 Express has the following features for advanced HDD diagnostic and troubleshooting: Furthermore, each channel has feedback with the PC-3000 software for monitoring the stability of +5V and +12V voltage supply and informing the user about any problems in power circuits. In case of emergency, the HDDs will be powered off automatically. The Power Supply Unit protects the HDDs from overvoltage and overcurrent. This has become possible because of efficient use of hardware buffering of the data transferred from the 4 UDMA ports through the PCI-Express 4-channel bus.Ī 4-channel Power Supply Unit is used to power the HDDs which are connected to PC-3000 Express. Performance is maintained almost at the same level even when all ports have simultaneous loads. ![]() PATA x2 - UDMA100, UDMA66, UDMA33, PIO4, PIO3, PIO2, PIO1, PIO0Īll ports are separable and independent. ![]() As a result, we have achieved a significant increase in performance and efficiency, making this professional product the best tool for the contemporary data recovery industry. When developing the new PC-3000 Express system we used our “know-how”, all gained experience and requests from our users who work in data recovery. Thus, you can work either with 4 SATA drives or 2 SATA and 2 PATA at the same time. You can connect four drives to the PC-3000 Express simultaneously - two SATA drives and two SATA or PATA drives, depending on your needs. The primary ports are SATA0 and SATA1 while SATA2 and SATA3 are switchable with the PATA ports (PATA0 and PATA1). Six diagnostic ports are 4 SATA ports (data transfer speed up to 133 Mb/sec) and 2 PATA ports (speed up to 100 Mb/sec). The new powerful PC-3000 Express is a six-port tester-board which is inserted into a PCI-Express expansion slot. If you wish to repair these HDDs, you need only the PC-3000 Express, and for data recovery you need both the PC-3000 Express and the Data Extractor Express. The PC-3000 Express coupled with the Data Extractor Express forms the PC-3000 Express Professional System that enables you to recover data from SATA, and PATA (IDE) HDDs. The PC-3000 Express is a hardware-software solution intended for diagnosing and repairing HDDs based on SATA (Serial ATA) and PATA (IDE) interfaces for numerous vendors (Seagate, Western Digital, Fujitsu, Samsung, Maxtor, Quantum, IBM (HGST), HITACHI, TOSHIBA), for various capacities (from 500 MB to 8 TB) and various form factors: 3.5" - desktop drives, 2.5" and 1.8" - laptop drives.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |